Minimoto con dos encendedores, cómo se hace | Te Digo Cómo

Minimoto con dos encendedores, cómo se hace | Te Digo Cómo


What’s up friends? now you say how this is done we will learn to do one minibike with two lighters spent like this need cutter, flat screwdriver, pliers, super glue or strong glue Now we take the encenedores and started dismantling We use almost all parts let’s start with the metal cover stone continue with the friction, careful not to skip the flint as it takes a spring below click on the thumbnail and you will see how you can make a bomb sparks with materials left over us Now we move to remove the orchid with the screwdriver carefully pry you do not break this piece is key in the process of assembling the minimoto will be the next thing we will remove the gas pressure regulator and then desenroscaremos to remove the valve by doing this we will come out the remaining gas once we have taken We will keep the piece to remove it later and the thin screwdriver continue removing pieces inside the next piece that will remove is the one that will hold all the pieces of the minimoto also should remove it carefully not to break and so we have to keep everything disassembled to finish where we catch the pump will draw the valve and then we use spring This we will do holdin with pliers and unscrew the plastic part with this we will have finished removing the igniter we will do the same with the other lighter while performing this process I recommend that you pay attention what this guy says there handsome and if you have not already download our application for google chrome and follow us on facebook, twitter, google +, taringa and Tuenti we will proceed with the assembly, but before we give some holes in the plastic piece larger than we and that will serve to anchor all the other pieces the first cut will be wedge-shaped to engage subsequently orchid the second cut will be made in the other room and we will in circular shape and the same size as the piece that we will use to make the handlebars in this case the driver has the same size we must also look at these pieces have a larger part on one side and the other smaller the largest parts go together and now, autopilot and started to ride as we see, if properly installed, everything fits well and almost would not need to put glue but to make it hard and not unmount we are going to put with these pieces assemble the handlebar if the spring comes very fair, as is the case, I’ll stick with care and patience and once we put it mounted the hole we did previously now we measure and cut in half, more or less then put the dock and put some glue the other piece that completes the handlebar We make another cut here and apply glue thanks to the spring retainer parts cleave without that we holdin so that the minibike to roll and not touch the plastic we have to do another cut before pasting definitely In this step we must take care not to cut us and do so always with adult supervision with the pieces in place and securely apply glue in the joints of the two parts top and bottom on both sides once you have done this we have the finished base and securely fastened with glue the following will be doing the tailpipes that we will do what we overran parts handlebar and valve once we have gotten cut here and we return it to put creating a dual exhaust We do the same with the other valve We glue and we measure to get him and that is secure here we have to take care of when the exhaust peguemos not be playing with the rear wheel since slow down and would not let us shoot once attached such that we would like now cutting through here so it does not protrude we’re going to do the odometer and we will do with this pair of pieces with the metal cover to remove at first we will simulate the fairing this piece does not need glue, just put it this way adjusted and will stay fairly fixed apply glue to finish, we cut our surplus part and we stick the two together as we see this minimoto is full of details and thus we are left once completed Here is a visual summary of the pieces that we have needed for minimoto and video here today, if you give liked you like, add it to favorites and share on your social networks with your friends if you have any question or request, do not forget to leave comments on this video greetings and see you in the next and this is how it is done, if you like do not forget to subscribe to our youtube channel and visit our website www.tedigocomosehace.com Click on the thumbnails to continue watching videos Te Digo how it’s done and do not forget your ideas and suggestions for future videos on feedback from our channel